Atomic layer processing for carbon nanoelectronics
- Author
- N.F.W. Thissen
- Year
- 2017
- Abstract & Cover
- Source of Information
- https://research.tue.nl/en/publications/atomic-layer-processing-for-carbon-nanoelectronics
- University
- Eindhoven University of Technology (Eindhoven, Netherlands)
- External Link
- Read Thesis
Graphene and carbon nanotubes (CNTs) have long been proposed as ideal candidates to replace silicon in future nanoelectronic devices and have therefore attracted considerable attention from the scientific community. Regardless, these carbon nanomaterials struggle to leave the lab as many challenges for large-scale integration still exist. This thesis addresses several of these challenges including high electrical contact resistance to graphene and control over the synthesis of CNTs. Novel applications of atomic level nanofabrication techniques such as atomic layer deposition (ALD) and charged-particle beam processing have been explored for this purpose. For the fabrication of graphene devices, graphene sheets must be patterned into individual devices, and then contacted to form electrical connections. The conventional approach involves lithography using resist films. To avoid contamination by resist residues as much as possible, a direct patterning and contacting approach was developed. A focused ion beam (FIB) is able to directly etch graphene from a substrate. In Chapter 4, it was established that ions were being scattered in the residual gas of the FIB vacuum chamber, causing damage at remarkable distances from the intended target area. By optimizing the pressure as well as reducing the amount of ions used, the scattering could be minimized making FIB patterning a feasible alternative to conventional lithography. Next, the FIB-patterned graphene was used to fabricate and characterize electrical devices. As described in Chapter 5, for the first time contacts were deposited by ALD using an area-selective Pt ALD process which further avoids the use of resist films. A thin seed layer of Pt is first deposited on the graphene in the desired contact shape by electron-beam induced deposition (EBID), and then thickened to form pure Pt contacts by area-selective ALD. The ALD-contacted devices show remarkable improvements compared to conventionally deposited Pt contacts. Electrical measurements revealed clear evidence of contact-induced doping and an unexpected strong Pt-graphene coupling. The coupling may be controlled in the future by modifying the contact seed layer properties. The synthesis of single-walled carbon nanotubes (SWCNTs) requires very small catalyst nanoparticles (2-3 nm) from which the CNTs grow. In Chapter 6, ALD was found to be a very reliable alternative technique for the deposition of such nanoparticles, due to its ultimate control over the film thickness and ability to deposit films conformally around challenging 3-dimensional topographies. Co3O4 films between 0.02 – 1 nm deposited by ALD were established to be ideal for forming catalytic Co particles for CNT growth. By varying the initial film thickness (number of ALD cycles), the diameter and density of the catalysts and therefore CNTs could be accurately controlled. Co catalyst particles could also be deposited around nanowires, and CNT growth on challenging substrates was demonstrated. Furthermore, Co3O4 was combined with ALD Fe2O3 to form the popular Fe/Co bimetallic catalyst with which the CNT density could be increased. The low temperature requirement of Co3O4 ALD enabled the use of standard electron-beam lithography such that the catalyst could be deposited where required. Additionally, the use of ALD enables further improvements for catalyst design, for example by exploiting the possibility of area-selective deposition. Specifically, it was demonstrated in Chapter 7 that Fe2O3 films could be deposited selectively on Pt and Ir substrates using a novel ALD process. This process was used in Chapter 8 to form Fe/Pt alloyed nanoparticles for CNT growth while exploiting the good diameter and density control of Pt ALD nanoparticles. During CNT synthesis the Fe2O3/Pt reduce to form Fe/Pt particles which were demonstrated to be active for CNT growth. Finally, the Pt seed particles may also be deposited by EBID such that the placement of the catalyst particles, and eventually the CNTs, can be controlled at the nanoscale. To summarize, this thesis demonstrates nanofabrication techniques including EBID, FIB and ALD and their novel applications in carbon nanoelectronics, including patterning and contacting graphene as well as synthesis of CNTs. Most of the presented work has been or will be published in peer-reviewed scientific journals and will contribute toward integration of carbon nanomaterials for a wide range of applications. Moreover, the demonstrated novel applications of nanofabrication techniques are not limited to carbon nanoelectronics alone, but may be more generally applicable to related one- and twodimensional materials.
