Thin film materials for Li-ion batteries made by atomic layer deposition

Author
Knut Bjarne Gandrud
Year
2014
Abstract & Cover

The aim of this work was to synthesize thin films of a few selected lithium battery cathode materials by ALD, and further investigate how the electrochemical performance of these materials was influenced by the film thickness at the nm-level. Here, we will first quickly present some of the main findings in each paper, before a more general conclusion will be made at the end. An ALD process for deposition of FePO4 was developed, utilizing the precursor pairs of Fe(thd)3 + O3 together with Me3PO4 + (H2O + O3). This process yields amorphous films, and has an ALD window from 246 to 360 ºC. As-deposited amorphous 46 nm thick films shows excellent electrochemical behaviour, where theoretical capacities are reached at a current rate of 1 C. Furthermore, an increase in the capacity is observed during galvanostatic cycling at 1 C, resulting in a 3% increase from the initial capacity after 600 cycles. Lithium was successfully incorporated into the FePO4 process by addition of the Li(thd) + O3 process at 246 ºC, yielding amorphous LixFePO4 films. Heat treatment of the obtained films under reducing atmosphere resulted in crystallization of the olivine-type LiFePO4 phase. However, TOF-ERDA measurements revealed that the process is rather unstable, and the highest lithium content obtained corresponds to an overall composition of Li0.5FePO4. In retrospect it might be a good thing that the ALD process for the more well-know battery cathode LiFePO4 did not succeed, as then the exiting electrochemical properties of the amorphous FePO4 material might not have been discovered. Electrochemical investigation of amorphous FePO4 electrodes with thicknesses from 12 to 93 nm reveals a strong correlation between the electrode thickness and the electrochemical properties. Any added mass by increasing the thickness above 46 nm does not seem to be electrochemically active, resulting in greatly reduced electrochemical performance. However, record breaking electrochemical properties were, surprisingly, found for the thinner films with thicknesses of 12 and 23 nm. Analysis by cyclic voltammetry reveals that the peak currents scales with the sweep rate, demonstrating that these electrodes exhibit extremely facile kinetics, comparable to that found for supercapacitors. Specific powers above 1 MW/kg FePO4 are observed for the 12 nm thick electrode, where ~50% of its theoretical capacity can still be reversibly accessed. The 23 nm electrode shows excellent lifetime behaviour, where the initial capacity is only reduced by 24% after 10 000 cycles at 320 C. In addition, self-enhancing kinetics are observed for the 23 nm electrodes suggesting some form of optimization of the lithium ion transport during cycling. This self enhancing mechanism results in a 75 % increase in the capacity during galvanostatic cycling at the ultra high-rates of 320 C. The thickness dependent electrochemical properties of highly nano-textured V2O5 were also investigated. The sample deposited from 500 ALD cycles showed superior rate-performance compared to the other tested electrode thicknesses ranging from 250 – 5000 ALD cycles. Specific powers of 395 kW/kg V2O5 could be obtained, comparable with that of a supercapacitor, where 20% of its 1 C capacity could be reversible accessed. In addition to displaying high power capabilities, the 500 ALD electrodes could also be cycled for 1500 cycles at 120 C before the initial capacity dropped below 80%. Such a combination of high power capabilities and lifetime behaviour has, to our knowledge, not been reported before for V2O5. Regarding lithium based ALD-processes, the main conclusion is, that lithium is a challenging element to work with both regarding characterization and process development. However, this is a rapidly increasing field and it is certain that in the years to come a lot of progress will be made, together with an increased fundamental understanding of lithium based ALD-processes. Thus, through the initial goal to investigate the electrochemical properties of a few selected cathode materials, we have in this work shown the importance of conformal and precise thickness control for electrodes with poor electronic/ionic conductivities, for optimized performance in lithium batteries. Furthermore, we have also shown that through precise thickness control we can reveal the true rate capabilities of a material. This is achieved through a combination of factors such as, conformal and precisely controlled thickness of the electrode to the current collector. In addition, the electrodes contains no binders or conductive additives, which otherwise could had concealed the true rate capabilities of the electrode material itself. From our investigations we can also report, for the first time, that the exotic phenomenon termed rapid intercalation pseudocapacitance is observed in an amorphous material. These amorphous FePO4 electrodes show the highest reported specific power regardless of modification for the well-know battery material LiFePO4, and to our knowledge, the highest reported value for any battery cathode material. These results show that amorphous materials, which have been an overlooked group, might offer hope for substantial improvements in the performance of lithium batteries. Finally, the possibilities that the ALD technique offers, being able do deposit thin high-rate materials together with the capabilities of utilizing high-surface area substrates, are promising for development of an energy device that combines the energy density of batteries with the power density of supercapacitors.

Source of Information
Henrik Sonsteby
University
University of Oslo
(Oslo, Norway)
External Link
Read Thesis
LinkedIn
linkedin invite