Polymer hybrid thin-film composites with tailored permeability and antifouling performance
- Author
- Juha Nikkola
- Year
- 2014
- Abstract & Cover
- Source of Information
- FinALD40 exhibition material, http://www.aldcoe.fi/events/finald40.pdf
- University
- VTT Technical Research Centre of Finland / Tampere University of Technology (Oulu/Tampere, Finland)
- Read Thesis
In this thesis, thin-film composites (TFC) were fabricated and modified using various coating methods. Firstly, the aim was to create a TFC packaging film with tailored permeability [P1–P3]. It was essential to study the effect of atmospheric plasma pre-treatment and sol-gel coating layer on the oxygen (O2) and water vapour (WV) permeability. In addition, the thesis investigated the effect of sol-gel coating composition on the O2 permeability and oil repellence. Secondly, the aim was to investigate the effects of surface properties on the anti-fouling performance of coated polyamide (PA) TFC membranes [P4–P6]. Polyvinyl alcohol (PVA) and atomic-layer-deposition (ALD) were used to enhance the anti-fouling performance of TFC-PA membrane. Both antimicrobial and anti-adhesion approaches were studied so as to gain further understanding of the anti-fouling tendency. The main conclusions of the thesis are the following: SiOx coating was plasma-deposited on LDPE-boards. However, the SiOx coating did not improve the barrier performance of the LDPE-board. Therefore, a plasma-assisted sol-gel hybrid coating approach was considered for the LDPE-board. The composition of the two different sol-gel coatings (named SG204 and SG206) had an effect on barrier performances. The SG206 coating with more cross-linked 3D oligomer structure showed better O2 barrier performance in comparison to the SG204 coating with 2D oligomer structure. Nevertheless, the SG204 coating enhanced the oleophobicity of the LDPE-board, indicating improved grease barrier performance. The wettability and adhesion of the sol-gel coatings were enhanced when using the atmospheric plasma pre-treatment. Therefore, the plasma-activation of LDPE ensured the enhancement of O2 barrier performance for the SG206 coating and the grease barrier performance for the SG204 coating respectively. [P1–P2] The sol-gel coating (named SG200) was deposited on the PLA-board to form a smooth and hydrophilic primer layer. Besides the primer function, the SG200 coating showed a moderate improvement of O2 and WV barrier. The ALD-Al2O3 layers were successfully deposited on top of the SG200 coating. The ALD coating further enhanced the O2 and WV barrier performances. In fact, the TFC structure based on the ALD and sol-gel coatings had a somewhat better barrier performance compared to a plain ALD coating. [P3] Surface characterisation of commercially available uncoated and coated TFC-PA membranes revealed that the coating layer had a significant effect on the hydrophobicity, surface energy and roughness. In addition, the surface characterisation of experimental PVA-, PVA-PHMG- and ALD-coated TFC-PA membranes revealed an increase in the hydrophilicity and surface polarity. [P4–P6] All the coated membranes had better anti-fouling performance in comparison to uncoated TFC-PA membranes. The experimental PVA and ALD coatings showed anti-adhesion performance, showing a decrease in the attachment of the three model bacteria. The surface polarity correlated with the attachment of bacteria. The antimicrobial coatings with a higher PHMG percentage tended to have a higher bacteria-repellence and antimicrobial performance. CFU and DIZ results proved the antimicrobial performance of PHMG. [P4–P6] The PVA-, PVA-PHMG and ALD coatings had an effect on permeability and rejection of the TFC-PA membranes. PVA and PVA-PHMG coatings reduced the water and salt permeability and also, increased the salt rejection. Furthermore, the increase of the PHMG content showed a decrease in salt rejection. The thinner ALD coatings increased the water and salt permeability and also, reduced the salt rejection. However, the thicker ALD coatings reduced the water and salt permeability, while the salt rejection was slightly increased. [P5–P6] This study provides a basis for future development of TFC concepts with tailored permeability. Further research should focus on the effect of pre-treatment or primer layers to smooth the rough and heterogeneous polymer surfaces prior to the deposition of nanoscale inorganic coatings. In addition, the use of organic or inorganic-organic protective coatings could be considered, in order to improve the durability of an inorganic coating layer. Furthermore, tailoring of the coating com positions and combining of coating layer structures are expected to improve the barrier performance. An optimal anti-fouling surface could be obtained by applying a coating, which is a combination of anti-adhesion and antimicrobial performances. However, further optimisation of the coating composition is needed in order to create the anti-fouling performance without sacrificing the RO performance. In addition, further studies should include long-term fouling studies of the coated TFC-PA membranes. The ALD method has not been used for surface modification of RO membranes until now. Based on the first experiments, the ALD technology could be a promising candidate to modify RO membranes. In fact, even a low thickness of ALD coating could modify the surface properties of the RO membrane by increasing the hydrophilicity and polarity as well as by lowering the surface roughness. These properties are essential improvements, especially for anti-fouling and permeability. Despite the promising results obtained in this study, the parameters of the Al2O3- based ALD process need further investigation in order to find the balance between improved anti-fouling and RO performance. Moreover, investigations of other inorganic ALD chemistries are expected to provide new functionalities.
