Novel Corrosion Protective Nanostructured Composite Coatings
- Author
- Jay Mondal
- Year
- 2016
- Abstract & Cover
- Source of Information
- Väino Sammelselg
- University
- University of Tartu (Tartu, Estonia)
- External Link
- Read Thesis
In this study the preparation technology of GO and rGO nanomaterials and of their simple coatings, GO-PPy hybrid and rGO/3×(Al2O3/TiO2) composite coatings was elaborated and described, the coatings’ properties were investigated, and their performance to act as thin corrosion protective coatings was tested. The study was carried through in a complex way, using different thin film preparation techniques: spin-coating, electrochemical deposition, and atomic layer deposition, and a number of solid sample characterizations and testing methods available at both the Institute of Physics and the Institute of Chemistry of the University of Tartu were used. The extent of corrosion protective performance of the coatings before and after long-term immersion in salt solution was investigated through the measurement and determination of the open circuit potential, Tafel plots, voltamme try curves, electrochemical impedance, as well as by carrying through standard ASTM G48A salt test and long-time immersion in aqueous sodium chloride or potassium bromide solution, depending on the coating material and the substrate used. The main results and novelty of the studies presented in the thesis are as follows: Preparation of graphene oxide and reduced graphene oxide nanoplatelets, both as dispersions in water/polarized organic solvents and powders, us ing as raw material powder of natural graphite, and a modified mechano chemical method was introduced and exploited; Preparation technologies of thin GO and rGO simple coatings, GO-PPy hybrid and rGO/n×(Al2O3/TiO2) composite coatings were elaborated and exploited for coating AISI type 304 stainless steel and Ti-6Al-4V titanium alloy substrates. Spin coating was used for the preparation of the simple graphene based coatings, electrochemical deposition for the hybrid coating, and atomic layer deposition technique for the composite coating; The simple thin coatings of GO and rGO nanoplatelets exhibited a limited protection of the metallic substrates and can find usage in mild corrosive environments or for relatively short-term using. Nevertheless, the coat ings cannot protect the SS samples against the pitting corrosion in neutral salt solutions for a longer period; The hybrid GO-PPy coating on the SS substrate, with a thickness of ~ 10 µm, was the thickest one that was studied in this work, and it showed medium protection of the substrate, well withstanding a 72 h ASTM G48A standard immersion test. But after 144 h testing time cracks and openings were seen in the coating, which means that it had lost its protective character. For that reason, this type of coating could be used in medium corrosive environments and probably also in medicine for coat ing some implants and prostheses: the PPy is known as a biocompatible material, and the coating preparation technology allows to easily add into it drugs or anti-inflammatory impurities for better treatment of the patients during and after surgery. Unfortunately, this coating cannot be used on the surfaces exposed to hard mechanical contacts and/or wearing because of the low hardness and wearability of the material; The composite coating consisting of the rGO underlayer and the metal oxide laminate (3×(Al2O3/TiO2)) top layer prepared by the ALD method showed good corrosion inhibition properties, which were demonstrated by both the electrochemical measurements (increased pitting potential, decreased corrosion and passivation currents, and lowered coating poros ity) and the successful long-term salt solution immersion tests. It is important to point out that the laminate or the graphene layers alone could not protect the metal substrates against pitting corrosion; the possible rea sons are given and discussed in the thesis; Finally, three types of corrosion coatings developed and tested in this thesis showed different levels of corrosion inhibition and can be used in different applications. This allows us to declare that the application of the study results increases the lifetime and stability of metal parts and equipment made from these materials, helping to save materials and energy, and thus to develop a more sustainable society.
