Growth and characteristics of Ru based electrodes using RuO4 precursor for DRAM capacitor
- Author
- Cheol Hyun An
- Year
- 2019
- Abstract & Cover
- Source of Information
- Cheol Seong Hwang
- University
- Seoul National University (Seoul, Korea)
- Read Thesis
Recently, scaling of the Dynamic Random Access Memory (DRAM) device, which is widely used in almost microelectronic fields, has been progressing. Thus, the further scaling of the capacitor in DRAM is also required for next generation DRAM device. However, a certain amount of capacitance, ~25fF, should be maintained to operate DRAM device but it is so challenging due to decreasing capacitance area and limit of patterning technology. Therefore, the improvement of performance via the introduction of new materials. In recent studies, improving electrical performance using high-k materials such as TiO2 or SrTiO3 has been reported instead of HfO2 or ZrO2 based materials. The equivalent oxide thickness (EOT) could be lowered via introducing high-k materials, but adequate electrode should be selected to enhance the crystallinity of dielectric film and lower the leakage current following the low band gap energy. Kinds of noble metal based materials such as Ru, Ir, Pt having been spotlighted as electrode materials of next generation DRAM capacitor. Among them, Ru has high work function (~4.7eV), low resistivity (~7 uohm-cm), high chemical stability so that many studies on Ru metal film are reported. Almost Ru thin film deposition methods use metal-organic precursors having large ligand size, low vapor pressure, and reactivity which make it difficult to adopt on DRAM capacitor devices. In this study, therefore, growing Ru-based thin films and investigating the electrical performance of capacitors using RuO4 precursor, which has high reactivity and vapor pressure, are reported. Depositing methods of Ru, RuO2, or SrRuO3 materials using RuO4 precursor have been reported but those are based on CVD reaction. Thus, the ALD growth of Ru based films is investigated to achieve better conformality. Firstly, ALD of Ru metal films using RuO4 precursor and reduction gas has been investigated. To prevent the thermal decomposition of RuO4 precursor, the deposition was conducted at a lower temperature range than the previously reported CVD process. Ru metal films were grown on various oxide substrates, Ta2O5, ZrO2, and TiO2. On ZrO2 and TiO2 substrate, ordinary ALD-like growth behavior of Ru metal films was shown while unexpected growth behavior was shown on Ta2O5 substrate. The deposition amount of Ru metal film showed 2 self-limited steps versus reduction gas feeding time, which was not reported before. From the physical and chemical analysis of the film in each step, only pure Ru metal was deposited and any introduction of different phase like RuO2 was not present. Through the detailed analysis, the mechanism based on the reduction and diffusion of Ta2O5 substrate material was proposed to explain the extraordinary growth behavior. Despite its abnormal growth behavior, grown Ru films have low resistivity, low impurity and high step coverage. On ZrO2 and TiO2 surface, Ru metal film has good performance as on Ta2O5 surface. The high work function of Ru metal is expected to suppress the leakage current of high-k dielectric films, the improvement of electric characteristics of the capacitor with Ru top electrode was investigated. ZrO2/Al2O3/ZrO2 (ZAZ) and TiN were used and dielectric film and a bottom electrode, respectively. Sputter-grown TiN top electrode was used for comparison. Since Ru top electrode was deposited via the ALD process, the patterning process of Ru film is required. The Ru metal films were oxidized to RuO4 and etched, using O3 gas in ALD chamber. Comparing the electric characteristics of the Ru/ZAZ/TiN capacitor and TiN/ZAZ/TiN capacitor, the leakage current issue was significantly improved. The physical thickness of ZAZ film could be reduced due to lowered leakage current so that the EOT of Ru/ZAZ/TiN capacitor shrank to 75% of TiN/ZAZ/TiN capacitor, at the leakage current level of DRAM capacitor, 10-7 A/cm2 . From the detailed analysis of leakage conduction mechanisms, it could be demonstrated that not only the high work function of Ru metal but also the patterning process affected the improvement of leakage current issue. During the Ru top electrode patterning process, the introduced O3 gas recovered the oxygen vacancies in ZAZ dielectric film and the charge conduction was suppressed. Finally, the modified SrRuO3 deposition process for improving step coverage is studied. The previous SrRuO3 deposition process consists of ALD SrO cycles and CVD RuO2 cycles. SrO layers show excessive growth behavior so that the step coverage is not that good in conventional process. Thus, to prevent the oxygen absorption from RuO2 layer which induces the excessive growth of SrO layer, the reduction gas injection step is introduced after the RuO2 deposition step. From the modified deposition process, SrRuO3 layer shows step coverage about 95% on hole structure with 10:1 aspect ratio without any characteristic deterioration. Moreover, the surface roughness of SrRuO3 film in modified process is also significantly improved.
