Atomic-layer-deposited surface passivation schemes for silicon solar cells
- Author
- B.W.H. van de Loo
- Year
- 2017
- Abstract & Cover
- Source of Information
- https://research.tue.nl/en/publications/atomic-layer-deposited-surface-passivation-schemes-for-silicon-so
- University
- Eindhoven University of Technology (Eindhoven, Netherlands)
- External Link
- Read Thesis
Atomic-Layer-Deposited Surface Passivation Schemes for Silicon Solar Cells To achieve crystalline silicon (c-Si) solar cells with high energy conversion efficiencies, it is vital to suppress recombination of electrons and holes at the c-Si surface. In upcoming crystalline silicon solar cell concepts, a wide variety of textured and doped surfaces, including highly doped n+- and p+-type Si surfaces, is present. The conditions of these surfaces strongly influence surface recombination. This dissertation aims at the fundamental understanding and the improvement of the passivation of such surfaces by thin films that are prepared by atomic layer deposition (ALD). First, a literature review on the use of ALD in c-Si photovoltaics is presented. Besides discussing the physical principles and current status of surface passivation materials which are prepared by ALD, it is outlined that ALD is suitable for the preparation of other functional layers for c-Si photovoltaics as well, such as transparent conductive oxides and novel carrier-selective contacts. Secondly, SiO2/Al2O3 stacks prepared by ALD are investigated for the passivation of n+ as well as p+ Si surfaces. The stacks provide high levels of chemical passivation, whereas the density and polarity of fixed charges in the passivation stack can be varied by carefully tuning the SiO2 thickness. As a result, simultaneous passivation of n+ as well as p+ Si surfaces can be achieved. The working principles of the stacks are demonstrated in bifacial and interdigitated-back contact (IBC) solar cells, which have conversion efficiencies of 19.2% and 18.8%, respectively. Moreover, it is shown that the deposition of the SiO2/Al2O3 stacks can be scaled up in high-throughput batch ALD reactors, which makes the passivation scheme also of industrial interest. Next, a p-type doping process for c-Si solar cells is evaluated, which is based on the chemical vapor deposition of a (pure) boron source layer. It is found that low recombination rates could be realized by passivation of the surface by ALD Al2O3. Importantly, the drive-in of dopants has to be carried out in an oxygen containing ambient, to prevent the formation of a boron-rich layer which impedes surface passivation. In addition, the influence of the doping level on the surface recombination rate is scrutinized. It is found that for p+ Si, a high doping concentration (~1020 cm-3) is beneficial to further suppress surface recombination when field-effect passivation by a negative fixed charge density is absent. By wet chemical etching of the near-surface depletion region of p+ Si, the surface doping concentration is increased and charge-carrier recombination is reduced. Nanotextures, such as black Si, are of interest for c-Si photovoltaics due to their outstanding optical properties, although the passivation of surface defects is challenging due to the high surface roughness and the consequently enlarged surface area. In this work, it is established that for the nanotextures additional charge carrier recombination can take place through defects which reside underneath the surface. By wet chemical removal of this defective region and by using the earlier developed ALD SiO2/Al2O3 stacks, passivation of n+-type black Si surfaces is ultimately achieved without compromising the optical properties. In IBC solar cells, the p+ and n+ Si regions are adjacent, and pn-junctions are bordering at the rear surface. Charge carrier recombination near these pn-junctions is quantified by e.g., Suns-Voc measurements on specialized test structures that entail a varying junction density. It is demonstrated that a significant J02-recombination current at the pn-junction can be avoided when the surface is passivated by Al2O3/SiNx. Finally, passivation materials which can also function as carrier-selective contact are emerging, as they offer the potential of higher conversion efficiencies in combination with a straight-forward processing. The insights on surface passivation of c-Si surfaces gained throughout this dissertation are used to achieve surface passivation by transparent and conductive ZnO films. Excellent levels of passivation of lowly doped n- and p- type c-Si surfaces, with implied open-circuit voltages of 735 mV at 1-sun illumination, are realized by doped ZnO films prepared by ALD. Specifically, surface passivation is enabled by the use of an ultrathin (~ 1.5 nm) SiO2 tunnel oxide, the use of an Al2O3 capping layer during post-deposition annealing, and the incorporation of extrinsic n-type dopants (i.e., Al and B) in the ZnO. Additionally, the role of hydrogen in the passivation mechanism is revealed by isotope labeling and secondary ion mass spectroscopy. As the passivating ZnO films are also conductive and suitable as anti-reflection coating, the films are of high interest as transparent passivating electron contact. To conclude, it is underlined that key virtues of ALD, such as the soft deposition of e.g., ZnO on the underlying tunnel oxide, the accurate control over the doping level, the possibility to make complex film stacks, and the high conformality of thin films on nanotextures, make ALD a very versatile technique for the preparation of surface passivation layers for silicon solar cells.
